1 x 3 Hemmed Aluminum Drip Edge Flashing - Sold by Foot
1 x 3 Hemmed Aluminum Drip Edge Flashing - Sold by Foot
Couldn't load pickup availability
1 x 3 Hemmed Aluminum Drip Edge | 3 in Roof Leg | 1 in Face | Folded Lower Hem | Sold by Foot | Ships up to 8 ft
1 x 3 Hemmed Aluminum Drip Edge Flashing - Sold by Foot
Give the roof edge a cleaner, more finished water break before the gutter line has to do the hard work. This hemmed aluminum drip edge uses a 3 in roof leg, 1 in face, and folded lower hem for roof-edge, fascia, and gutter transition work that needs clean coverage without a bulky front face.
Order the Exact Footage Your Roof Edge Needs
This hemmed aluminum drip edge is sold by the linear foot. Enter the total footage needed for the roof edge, gutter run, eave, rake, fascia transition, repair section, or exterior edge detail.
Full section reference: this profile is commonly handled in 10 ft sections. Order quantity should still reflect total linear feet needed.
Shipping limit: shipped pieces are limited to 8 ft maximum length because long formed metal is costly to package and more likely to bend during transit.
Need longer pieces? Ask about pickup at GutterAll in Damascus, Oregon or local delivery where available.
A Folded Hem for a Cleaner Finished Edge
The hemmed lower edge is the standout detail on this profile. The folded hem helps create a cleaner visible edge than raw flat metal and adds rigidity to the lower return, making it a smart choice for roof-edge and gutter-adjacent work where the finished line matters.
Best fit: compatible eave flashing, rake flashing, roof-edge flashing, gutter-edge flashing, fascia-side coverage, gutter replacement prep, exterior repair runs, and projects that need a 3 in roof leg with a lower 1 in face.
The Edge Detail Is Where the Job Either Looks Finished — or Patched
A gutter install can be measured perfectly and still look rough if the roof edge above it is short, exposed, bent, or unfinished. This 1 x 3 hemmed aluminum drip edge gives crews a cleaner roof-to-gutter transition for compatible assemblies, especially where a 3 in roof leg is preferred over compact 1.5 in or 2 in profiles.
Cleaner edge metal helps the finished gutter detail look intentional, measured, and ready for a professional handoff.
Lightweight Aluminum with Multiple Color Options
The aluminum construction gives contractors a lightweight formed metal profile for exterior roof-edge and gutter-adjacent work. Multiple color options help coordinate the flashing with gutters, fascia, trim, siding, roof accents, and exterior color schemes.
Confirm color, piece length, roof-edge fit, fastener method, and surrounding material compatibility before ordering.
Fast Reasons This Profile Gets Picked
Hemmed Lower Edge
The folded lower hem creates a cleaner finished edge and adds rigidity compared with an unfinished lower edge.
3 in Roof Leg
Gives wider roof-side coverage than smaller 1.5 in or 2 in roof-leg profiles where compatible.
Low 1 in Face
Keeps the fascia-side edge lower and cleaner than taller face profiles.
Measured Footage
Sold by foot so crews can order for the actual run instead of guessing around fixed pieces.
Profile Details
| Profile Area | Measurement | Why It Matters |
|---|---|---|
| Roof leg | 3 in | Gives wider roof-side coverage than compact 1.5 in or 2 in roof-leg profiles where compatible. |
| Face / drop | 1 in | Creates a lower fascia-side edge than 1.5 in or 2 in face profiles. |
| Lower edge | Hemmed / folded lower return | Creates a cleaner finished edge and adds rigidity to the profile. |
| Profile bend | Default 120° bend shown | Defines the formed transition between the roof leg and face. |
| Material | Aluminum | Provides a lightweight formed flashing profile for exterior roof-edge work. |
Footage, Sections, and Delivery Lengths
| Detail | What to Know Before Ordering |
|---|---|
| Sold by foot | Order the total number of linear feet needed for the run. |
| 10 ft section reference | The product is referenced as 10 ft sections, but order quantity should reflect total linear footage. |
| Shipping length | Shipped pieces are limited to 8 ft maximum length. |
| Pickup | Longer pieces may be available for pickup at GutterAll in Damascus, Oregon. |
| Local delivery | Longer pieces may be available for local delivery depending on order size and route. |
Best-Fit Applications
| Application | Why It Fits |
|---|---|
| Roof-edge water control | The 3 in roof leg gives solid roof-side coverage for compatible eave and rake details. |
| Gutter installation prep | Useful when the gutter install also needs a clean roof-edge transition before the gutter line is finished. |
| Low-profile fascia edge | The 1 in face creates a lower front edge where taller face coverage is not needed. |
| Finished lower edge detail | The hemmed return creates a cleaner folded edge than raw flat trim metal. |
| Repair and replacement runs | Sold-by-foot ordering helps match material quantity to measured job sections. |
1 x 3 Hemmed Drip Edge vs Non-Hemmed Profiles
| 1 x 3 Hemmed Aluminum Drip Edge | Non-Hemmed or Smaller Profiles |
|---|---|
| Hemmed lower return for a cleaner finished edge. | May leave a more exposed lower edge depending on profile style. |
| 3 in roof leg for more roof-side coverage than compact profiles. | 1.5 in or 2 in roof legs may be better where less roof-side coverage is needed. |
| 1 in face for a lower-profile fascia-side edge. | 1.5 in or 2 in faces may be better when more vertical fascia-side coverage is needed. |
| Aluminum construction for lightweight handling. | Other profiles may use steel, copper, or different materials depending on project needs. |
Key Features
| Feature | Customer Benefit |
|---|---|
| Hemmed lower edge | Creates a cleaner folded edge and adds profile rigidity. |
| 3 in roof leg | Gives wider roof-side coverage than smaller roof-leg profiles where compatible. |
| 1 in face | Keeps the fascia-side edge lower than taller face profiles. |
| Aluminum construction | Provides a lightweight formed flashing profile for exterior roof-edge work. |
| Sold by foot | Lets crews order by measured project footage. |
| 8 ft maximum shipped length | Keeps shipped flashing pieces within a more practical long-item shipping size. |
Quick Product Summary
1 x 3 Hemmed Aluminum Drip Edge Flashing for eave, rake, roof-edge, fascia, gutter-adjacent, and exterior transition work. The profile shown has a 3 in roof leg, 1 in face, default 120° bend, and hemmed lower edge. Sold by foot for measured project runs. The product is referenced in 10 ft sections; shipped pieces are limited to 8 ft maximum length because long formed metal is expensive to ship. Longer pieces may be available for pickup or local delivery.
Job-Site Advantages
- Hemmed lower edge creates a cleaner folded finish
- Folded return adds rigidity compared with raw lower-edge trim
- 3 in roof leg gives roof-side coverage where compatible
- 1 in face creates a lower-profile fascia-side edge
- Aluminum construction supports lightweight handling
- Multiple color options help match gutters, fascia, trim, siding, and roof accents
- Sold by foot for cleaner project quantity planning
- 10 ft section reference helps crews plan common run lengths
- Shipped pieces limited to 8 ft for practical long-item delivery
- Longer pieces may be available for pickup or local delivery
- Useful for eave, rake, roof-edge, fascia, gutter-adjacent, and trim transition details
- Helps guide roof runoff toward the gutter path when installed correctly
- Good option for gutter installers, roofers, remodelers, and exterior crews
- Practical for repair work, replacement work, and new exterior installations
- Works with compatible fasteners, sealants, roofing materials, and flashing methods
Product Specifications
| Specification | Details |
|---|---|
| Product Name | 1 x 3 Hemmed Aluminum Drip Edge Flashing - Sold by Foot |
| Product Type | Hemmed drip edge flashing, aluminum drip edge, roof-edge flashing, gutter-edge flashing, fascia flashing, eave flashing, rake flashing |
| Profile Size | 1 x 3 nominal profile |
| Roof Leg | 3 in |
| Face / Drop | 1 in |
| Lower Edge | Hemmed / folded lower return |
| Profile Bend | Default 120° bend shown in profile drawing |
| Material | Aluminum |
| Color Options | Multiple colors available; confirm current color options before ordering. |
| Sold As | Per linear foot |
| Ordering Basis | Order total linear feet needed for the project. |
| Full Section Reference | 10 ft section reference |
| Shipping Length Limit | Maximum 8 ft per shipped piece |
| Longer Pieces | Ask about longer pieces for pickup or local delivery before ordering. |
| Primary Uses | Roof-edge details, eave flashing, rake flashing, fascia coverage, gutter-adjacent transitions, repair runs, and exterior water-control details |
| Best Fit | Projects needing a 3 in roof leg, 1 in face, and hemmed lower edge in a formed aluminum drip edge profile |
| Common Accessories | Compatible fasteners, sealant, snips, roof safety gear, underlayment, roofing materials, gutter components, and fascia repair materials as needed |
| Confirm Before Use | Roof-edge assembly, gutter position, fascia condition, overlap direction, fastening method, roof safety plan, color match, and whether a different flashing profile is required |
| Not Intended For | Applications requiring gutter apron, wall step flashing, metal roof-specific flashing, tile roof flashing, structural support, or installation that conflicts with local requirements or manufacturer instructions |
| Expected Service Life | Varies by finish condition, climate exposure, installation quality, cut edges, fastener choice, sealant use, drainage conditions, maintenance, and compatibility with surrounding materials. |
Who Uses This Hemmed Drip Edge?
Gutter Installers and Exterior Crews
- Preparing roof-edge details before or during gutter installation
- Using a hemmed lower edge where a cleaner finished profile is preferred
- Ordering exact footage for repair, replacement, and project runs
Roofers, Remodelers, and Builders
- Using an aluminum hemmed drip edge profile for compatible roof-edge layouts
- Choosing multiple color options where exterior finish coordination matters
- Planning order footage around eaves, rakes, fascia runs, and repair sections
Experienced DIY Buyers
- Replacing compatible roof-edge flashing near gutter and fascia details
- Ordering smaller project quantities by the foot
- Using 8 ft or shorter shipped pieces for manageable handling
Installation Planning Guide
- Measure the total eave, rake, roof-edge, fascia, repair, or gutter-adjacent transition footage needed.
- Order the total number of linear feet required.
- Plan around the 10 ft section reference when estimating pickup or local delivery needs.
- For shipped orders, plan around an 8 ft maximum piece length.
- Confirm the selected color works with the gutter, fascia, roof, siding, and trim.
- Confirm whether the 3 in roof leg, 1 in face, and hemmed lower return fit the actual roof-edge detail.
- Use proper flashing sequence, overlap direction, drainage clearance, and compatible surrounding materials.
- Use compatible fasteners and sealants for the roofing and gutter system.
- Check fit and water path before fastening the full run.
- Verify runoff is directed outward and toward the gutter path without running behind the fascia.
Installation and Ordering Notice
This flashing is sold per linear foot. The product is referenced as 10 ft sections. Shipped pieces are limited to 8 ft maximum length because long formed metal is costly to ship and more likely to bend or damage during transit.
For longer pieces, use pickup or ask about local delivery availability before ordering.
Use proper flashing sequence, overlap, drainage clearance, compatible fasteners, and sealant practices for the roof and gutter system being worked on.
Use safe ladder practices, gloves, eye protection, and fall protection when working at roof or gutter height. Cut metal can be sharp, including cut or modified hemmed flashing.
Need Help Planning Footage, Color, or Cut Lengths?
Use website chat for help planning total footage, shipped cut lengths, pickup options, local delivery availability, and whether this 1 x 3 hemmed aluminum drip edge profile is the right fit for the roof-edge detail.
Order by Footage
Order the total linear feet needed for the project.
10 ft Section Reference
Useful for pickup, local delivery, and project planning.
Ships up to 8 ft
Shipped pieces are cut to 8 ft or less for practical delivery.
Product Summary Box
1 x 3 Hemmed Aluminum Drip Edge Flashing for eave, rake, roof-edge, fascia, gutter-adjacent, and exterior transition work. The profile shown has a 3 in roof leg, 1 in face, default 120° bend, and hemmed lower edge. Sold by foot for exact project footage. The product is referenced in 10 ft sections; shipped pieces are limited to 8 ft maximum length because long formed metal is expensive to ship. Longer pieces may be available for pickup or local delivery.
Frequently Asked Questions
What is 1 x 3 hemmed aluminum drip edge flashing used for?
It is used for compatible eave, rake, roof-edge, fascia, and gutter-adjacent details where an aluminum drip edge profile with a 3 in roof leg, 1 in face, and hemmed lower edge fits the project.
How is this flashing ordered?
It is sold by the foot. Order the total linear footage needed for the project. The product is referenced as 10 ft sections, while shipped pieces are limited to 8 ft maximum length.
What does the hemmed edge do?
The hemmed lower edge creates a folded finish and adds profile rigidity compared with a raw lower edge. Cut or modified metal can still be sharp, so gloves and safe handling are still important.
Can pieces longer than 8 ft be shipped?
No. Shipped pieces are limited to 8 ft because long formed metal is costly to package and more likely to bend during transit. Longer pieces should be arranged through pickup or local delivery where available.
Is this the same as gutter apron?
No. This is hemmed aluminum drip edge flashing. Gutter apron is a different roof-edge profile and may be better for certain roof-to-gutter details.
What is GutterAll's return policy for this product?
GutterAll offers a 30-day return window for unused standard products in original condition. Cut, bent, scratched, installed, altered, custom-length, custom-color, or customer-damaged flashing may not be returnable unless defective. Customers should confirm footage, piece length, color, profile, pickup, delivery, and shipping limits before ordering. Return shipping or return transport is the buyer's responsibility unless the return is due to defect or fulfillment error. Refunds are processed within 5 to 7 business days after approval and receipt.
What fulfillment options are available?
In-store pickup at GutterAll in Damascus, Oregon, local delivery where available, and shipping are available depending on selected piece length. Shipped pieces are limited to 8 ft. Typical small-order handling is 1 to 2 business days, and transit time is typically 3 to 7 business days depending on destination and carrier.
Address
GutterAll
19759 SE Sunnyside Rd
Damascus, OR 97089
Hours
Mon-Fri: 7am-4pm PST
Sat: 9am-12pm PST
sales@gutterall.com
Phone
(503) 850-6784
